hylafax/contribs7/hylafax_config.modem

# $Id: rockwell,v 1.2 1996/06/24 02:58:40 sam Rel $
#
# HylaFAX Facsimile Software
#
# Copyright (c) 1990-1996 Sam Leffler
# Copyright (c) 1991-1996 Silicon Graphics, Inc.
# HylaFAX is a trademark of Silicon Graphics, Inc.
# 
# Permission to use, copy, modify, distribute, and sell this software and 
# its documentation for any purpose is hereby granted without fee, provided
# that (i) the above copyright notices and this permission notice appear in
# all copies of the software and related documentation, and (ii) the names of
# Sam Leffler and Silicon Graphics may not be used in any advertising or
# publicity relating to the software without the specific, prior written
# permission of Sam Leffler and Silicon Graphics.
# 
# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND, 
# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY 
# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
# 
# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF 
# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE 
# OF THIS SOFTWARE.
#

#
# Configuration for a Rockwell-based modem not otherwise handled by
# another prototype configuration file.  This file assumes the modem
# is compatible with the Rc144AC, RC96AC or RC144DP.
#
# This configuration file sets up the modem to run at 38.4 with
# RTS/CTS flow control used by default.  XON/XOFF is automatically
# enabled for fax recv.  Beware of modems that also lock sending
# to 19.2; add ModemSendBeginCmd: "<19200>" if this is required.
# Also beware that the adaptive-answer facility, when supported,
# is often unreliable.
#
#
CountryCode:            1
AreaCode:               999
FAXNumber:              +1.999.555.1212
LongDistancePrefix:     1
InternationalPrefix:    011
DialStringRules:        "etc/dialrules.sf-ba"
ServerTracing:          1
SessionTracing:         11
RecvFileMode:           0600
LogFileMode:            0600
DeviceMode:             0600
RingsBeforeAnswer:      1
SpeakerVolume:          off
GettyArgs:              "-h %l %s"
LocalIdentifier:        "Silent Valley Sys"
TagLineFont:            etc/lutRS18.pcf
TagLineFormat:          "From %%l|%c|Page %%p of %%t"
MaxRecvPages:           25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType:              Class2          # use class 2 interface
ModemRate:              38400
ModemFlowControl:       rtscts          # default
#
ModemResetCmds:         AT&F                    # what you want for a Supra
ModemNoFlowCmd:         AT&K0           # disable flow control cmd
ModemHardFlowCmd:       AT&K3           # hardware flow control cmd
ModemSoftFlowCmd:       AT&K4           # software flow control cmd
ModemSetupDTRCmd:       AT&D3           # DTR off causes modem to reset
#ModemSetupDTRCmd:      AT&D2S25=1S38=0 # Dynalink 1414VE needs this
ModemSetupDCDCmd:       AT&C1           # DCD follows carrier
ModemSetupAACmd:        AT+FAA=1+FCLASS=0 # enable in current class
#
ModemSendFillOrder:     LSB2MSB         # as expected
ModemRecvFillOrder:     MSB2LSB         # opposite of what makes sense
#
ModemAnswerFaxBeginCmd: "<19200><rts>"  # modem switches on fax receive
#
# Caller ID configuration setup for Supra.
#
#QualifyCID:            etc/cid         # CID access control list file
#CIDNumber:             "NMBR = "       # pattern string for phone number info
#CIDName:               "NAME = "       # pattern string for identity info
Class2RecvDataTrigger:  "\022"          # character sent to modem to start recv


1	# $Id: rockwell,v 1.2 1996/06/24 02:58:40 sam Rel $
2	#
3	# HylaFAX Facsimile Software
4	#
5	# Copyright (c) 1990-1996 Sam Leffler
6	# Copyright (c) 1991-1996 Silicon Graphics, Inc.
7	# HylaFAX is a trademark of Silicon Graphics, Inc.
8	#
9	# Permission to use, copy, modify, distribute, and sell this software and
10	# its documentation for any purpose is hereby granted without fee, provided
11	# that (i) the above copyright notices and this permission notice appear in
12	# all copies of the software and related documentation, and (ii) the names of
13	# Sam Leffler and Silicon Graphics may not be used in any advertising or
14	# publicity relating to the software without the specific, prior written
15	# permission of Sam Leffler and Silicon Graphics.
16	#
17	# THE SOFTWARE IS PROVIDED "AS-IS" AND WITHOUT WARRANTY OF ANY KIND,
18	# EXPRESS, IMPLIED OR OTHERWISE, INCLUDING WITHOUT LIMITATION, ANY
19	# WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
20	#
21	# IN NO EVENT SHALL SAM LEFFLER OR SILICON GRAPHICS BE LIABLE FOR
22	# ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES OF ANY KIND,
23	# OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS,
24	# WHETHER OR NOT ADVISED OF THE POSSIBILITY OF DAMAGE, AND ON ANY THEORY OF
25	# LIABILITY, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
26	# OF THIS SOFTWARE.
27	#
28
29	#
30	# Configuration for a Rockwell-based modem not otherwise handled by
31	# another prototype configuration file. This file assumes the modem
32	# is compatible with the Rc144AC, RC96AC or RC144DP.
33	#
34	# This configuration file sets up the modem to run at 38.4 with
35	# RTS/CTS flow control used by default. XON/XOFF is automatically
36	# enabled for fax recv. Beware of modems that also lock sending
37	# to 19.2; add ModemSendBeginCmd: "<19200>" if this is required.
38	# Also beware that the adaptive-answer facility, when supported,
39	# is often unreliable.
40	#
41	#
42	CountryCode: 1
43	AreaCode: 999
44	FAXNumber: +1.999.555.1212
45	LongDistancePrefix: 1
46	InternationalPrefix: 011
47	DialStringRules: "etc/dialrules.sf-ba"
48	ServerTracing: 1
49	SessionTracing: 11
50	RecvFileMode: 0600
51	LogFileMode: 0600
52	DeviceMode: 0600
53	RingsBeforeAnswer: 1
54	SpeakerVolume: off
55	GettyArgs: "-h %l %s"
56	LocalIdentifier: "Silent Valley Sys"
57	TagLineFont: etc/lutRS18.pcf
58	TagLineFormat: "From %%l\|%c\|Page %%p of %%t"
59	MaxRecvPages: 25
60	#
61	#
62	# Modem-related stuff: should reflect modem command interface
63	# and hardware connection/cabling (e.g. flow control).
64	#
65	ModemType: Class2 # use class 2 interface
66	ModemRate: 38400
67	ModemFlowControl: rtscts # default
68	#
69	ModemResetCmds: AT&F # what you want for a Supra
70	ModemNoFlowCmd: AT&K0 # disable flow control cmd
71	ModemHardFlowCmd: AT&K3 # hardware flow control cmd
72	ModemSoftFlowCmd: AT&K4 # software flow control cmd
73	ModemSetupDTRCmd: AT&D3 # DTR off causes modem to reset
74	#ModemSetupDTRCmd: AT&D2S25=1S38=0 # Dynalink 1414VE needs this
75	ModemSetupDCDCmd: AT&C1 # DCD follows carrier
76	ModemSetupAACmd: AT+FAA=1+FCLASS=0 # enable in current class
77	#
78	ModemSendFillOrder: LSB2MSB # as expected
79	ModemRecvFillOrder: MSB2LSB # opposite of what makes sense
80	#
81	ModemAnswerFaxBeginCmd: "<19200><rts>" # modem switches on fax receive
82	#
83	# Caller ID configuration setup for Supra.
84	#
85	#QualifyCID: etc/cid # CID access control list file
86	#CIDNumber: "NMBR = " # pattern string for phone number info
87	#CIDName: "NAME = " # pattern string for identity info
88	Class2RecvDataTrigger: "\022" # character sent to modem to start recv
89
90
91
92
93
94
95
96