smeserver-freepbx/contribs9/smeserver-freepbx-0.1-full_dahdi_support.patch

diff -Nur -x '*.orig' -x '*.rej' smeserver-freepbx-0.1/createlinks mezzanine_patched_smeserver-freepbx-0.1/createlinks
--- smeserver-freepbx-0.1/createlinks   2009-02-12 00:22:09.000000000 +0100
+++ mezzanine_patched_smeserver-freepbx-0.1/createlinks 2009-02-12 00:20:26.000000000 +0100
@@ -14,10 +14,10 @@
 service_link_enhanced("httpd-fpbx", "K15", "0");
 service_link_enhanced("httpd-fpbx", "K15", "1");
 
-service_link_enhanced("zaptel", "S09", "7");
-service_link_enhanced("zaptel", "K16", "6");
-service_link_enhanced("zaptel", "K16", "0");
-service_link_enhanced("zaptel", "K16", "1");
+service_link_enhanced("dahdi", "S09", "7");
+service_link_enhanced("dahdi", "K16", "6");
+service_link_enhanced("dahdi", "K16", "0");
+service_link_enhanced("dahdi", "K16", "1");
 
 safe_symlink("../daemontools" , 'root/etc/rc.d/init.d/supervise/httpd-fpbx');
 safe_symlink("/var/service/httpd-fpbx" , 'root/service/httpd-fpbx');
diff -Nur -x '*.orig' -x '*.rej' smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/dahdi/status mezzanine_patched_smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/dahdi/status
--- smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/dahdi/status       1970-01-01 01:00:00.000000000 +0100
+++ mezzanine_patched_smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/dahdi/status     2008-09-20 14:06:51.000000000 +0200
@@ -0,0 +1 @@
+enabled
diff -Nur -x '*.orig' -x '*.rej' smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/dahdi/type mezzanine_patched_smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/dahdi/type
--- smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/dahdi/type 1970-01-01 01:00:00.000000000 +0100
+++ mezzanine_patched_smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/dahdi/type       2008-09-20 14:06:43.000000000 +0200
@@ -0,0 +1 @@
+service
diff -Nur -x '*.orig' -x '*.rej' smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/zaptel/status mezzanine_patched_smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/zaptel/status
--- smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/zaptel/status      2008-09-20 14:06:51.000000000 +0200
+++ mezzanine_patched_smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/zaptel/status    1970-01-01 01:00:00.000000000 +0100
@@ -1 +0,0 @@
-enabled
diff -Nur -x '*.orig' -x '*.rej' smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/zaptel/type mezzanine_patched_smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/zaptel/type
--- smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/zaptel/type        2008-09-20 14:06:43.000000000 +0200
+++ mezzanine_patched_smeserver-freepbx-0.1/root/etc/e-smith/db/configuration/defaults/zaptel/type      1970-01-01 01:00:00.000000000 +0100
@@ -1 +0,0 @@
-service
diff -Nur -x '*.orig' -x '*.rej' smeserver-freepbx-0.1/root/usr/share/freepbx/scripts/uninstall.sh mezzanine_patched_smeserver-freepbx-0.1/root/usr/share/freepbx/scripts/uninstall.sh
--- smeserver-freepbx-0.1/root/usr/share/freepbx/scripts/uninstall.sh   2008-08-13 13:22:56.000000000 +0200
+++ mezzanine_patched_smeserver-freepbx-0.1/root/usr/share/freepbx/scripts/uninstall.sh 2009-02-12 00:19:52.000000000 +0100
@@ -8,7 +8,7 @@
 echo "This script will remove from your server:"
 echo "     - freepbx and asterisk cdr MySQL databases"
 echo "     - freepbx MySQL User"
-echo "     - freepbx DB entries (freepbx, httpd-fpbx and zaptel)"
+echo "     - freepbx DB entries (freepbx, httpd-fpbx and dahdi)"
 echo "     - /opt/freepbx"
 echo ""
 echo -n "Are you sure you want to remove FreePBX permanently ? (y/n) [n] "
@@ -26,7 +26,7 @@
        echo "Removing SME DB entries..."
        /sbin/e-smith/db configuration delete freepbx
        /sbin/e-smith/db configuration delete httpd-fpbx
-       /sbin/e-smith/db configuration delete zaptel
+       /sbin/e-smith/db configuration delete dahdi
        echo "Removing /opt/freepbx ..."
        rm -rf /opt/freepbx
        echo "Removing this script ..."
diff -Nur -x '*.orig' -x '*.rej' smeserver-freepbx-0.1/root/var/lib/asterisk/bin/genzaptelconf mezzanine_patched_smeserver-freepbx-0.1/root/var/lib/asterisk/bin/genzaptelconf
--- smeserver-freepbx-0.1/root/var/lib/asterisk/bin/genzaptelconf       2009-02-12 00:22:09.000000000 +0100
+++ mezzanine_patched_smeserver-freepbx-0.1/root/var/lib/asterisk/bin/genzaptelconf     1970-01-01 01:00:00.000000000 +0100
@@ -1,570 +0,0 @@
-#! /bin/bash
-
-# genzaptelconf: generate as smartly as you can:
-#              /etc/zaptel.conf
-#              /etc/asterisk/zapata-channels.conf (to be #include-d into zapata.conf)
-#      update:
-#              /etc/default/zaptel (list of modules to load)
-#
-# $Id:$
-#      
-
-# The script uses a number of bash-specific features
-# TODO: either ditch them or convert to perl
-
-# /etc/default/zaptel may override the following variables
-lc_country=us
-#method=ls
-#method=ks
-base_exten=6000
-
-
-ZAPCONF_FILE=/etc/zaptel.conf
-ZAPATA_FILE=/etc/asterisk/zapata-auto.conf
-ZAPTEL_BOOT=/etc/sysconfig/zaptel
-exten_base_dir=/etc/asterisk/extensions-phones.d
-exten_defs_file=/etc/asterisk/extensions-defs.conf
-ztcfg_cmd=ztcfg
-
-# a temporary directory. Created when the switch -r is parsed on getopts
-# and deleted in the end on update_extensions_defs
-tmp_dir=
-
-# read default configuration from /etc/default/zaptel
-if [ -r $ZAPTEL_BOOT ]; then . $ZAPTEL_BOOT; fi
-
-# work around a bug (that was already fixed) in the installer:
-if [ "$lc_country" = '' ]; then lc_country=us; fi
-
-ALL_MODULES="wctdm wcfxo wcfxs pciradio tor2 torisa wct1xxp wct4xxp wcte11xp wcusb ztd_eth ztdummy"
-force_stop_ast=yes
-do_detect=no
-do_unload=no
-verbose=no
-rapid_extens=''
-# global: current extension number in extensions list. Should only be 
-# changed in print_pattern:
-rapid_cur_exten=1 
-# set the TRUNK in extensidialplan dialplan defs file  rapid_conf_mode=no
-
-die() {
-       echo "$@" >&2
-       exit 1
-}
-
-say() {
-       if [ "$verbose" = no ]; then
-               return
-       fi
-       echo "$@"   >&2
-}
-
-run_ztcfg() {
-       if [ "$verbose" = no ]; then
-               $ztcfg_cmd "$@"
-       else
-               say "Reconfiguring identified channels"
-               $ztcfg_cmd -vv "$@"
-       fi
-}
-
-do_update() {
-       sed -i.bak "s/^$1=.*\$/$1=\"$2\"/" ${ZAPTEL_BOOT}
-       if ! grep -q "^$1=" ${ZAPTEL_BOOT}; then
-               echo "$1=\"$2\"" >> ${ZAPTEL_BOOT}
-       fi
-}
-
-update_extensions_defs() {
-       if [ "$rapid_conf_mode" = 'yes' ]
-       then
-               say "DEBUG: Updating dialplan defs file $exten_defs_file"
-               if [ "`echo $tmp_dir/fxo_* | grep -v '*'`" != '' ]
-               then
-                       trunk_nums=`cat $tmp_dir/fxo_* | sort -n | xargs`
-                       say "Configuring TRUNK to be [first of] zaptel channels: $trunk_nums"
-                       trunk_dev=`echo $trunk_nums| sed -e 's/ /\\\\\\&/g' -e 's/[0-9a-zA-Z]\+/Zap\\\\\\/&/g'`
-                       echo >&2 sed -i "s/^TRUNK.*=>.*/TRUNK => $trunk_dev/" $exten_defs_file
-                       sed -i "s/^TRUNK.*=>.*/TRUNK => $trunk_dev/" $exten_defs_file
-                       if ! grep -q "^TRUNK =>" $exten_defs_file; then
-                               trunk_dev=`echo $trunk_nums| sed -e 's/ /&/g' -e 's/[0-9a-zA-Z]*/Zap\\/&/g'`
-                               echo "TRUNK => $trunk_dev" >> $exten_defs_file
-                       fi
-               else
-                       say "Warning: No FXO channel for trunk. Moving on."
-               fi
-               if [ "`echo $tmp_dir/fxs_* | grep -v '*'`" != '' ]
-               then
-                       fxs_nums=`cat $tmp_dir/fxs_* | sort -n | xargs`
-                       zap_nums=`grep '^[^;].*Zap/\${CHAN_ZAP_' $exten_base_dir/*.conf | \
-                               sed -e 's/.*Zap\/\${CHAN_ZAP_\([0-9]*\)}.*/\1/' | sort -u | xargs`
-                       say "Configuring channels: $fxs_nums as channel placeholders: $zap_nums"
-                       j=1
-                       for i in $zap_nums
-                       do
-                               chan=`echo $fxs_nums | awk "{print \\$$i}"`
-                               if [ "$chan" = '' ]
-                               then
-                                       # if the result is empty, we probably got past the last one.
-                                       # bail out.
-                                       say "Warning: No FXS channel for CHAN_ZAP_$i. Moving on"
-                                       break
-                               fi
-                               say "DEBUG: setting channel $chan to placeholder $i"
-                               if grep -q "^CHAN_ZAP_$i " $exten_defs_file
-                               then
-                                       sed -i -e "s/^CHAN_ZAP_$i .*/CHAN_ZAP_$i => Zap\/$chan/" $exten_defs_file
-                               else
-                                       echo "CHAN_ZAP_$i => Zap/$chan" >> $exten_defs_file
-                               fi
-                       done
-               fi      
-               # cleaning up the temp dir
-               if [ -d "$tmp_dir" ]; then rm -rf "$tmp_dir"; fi
-       fi
-}
-
-usage() {
-       program=`basename $0`
-
-       echo >&2 "$program: generate zaptel.conf"
-       echo >&2 "usage:"
-       echo >&2 " $program [-v] [-m k|l|g] [-c <country_code>] [-r |-e <base_exten>] "
-       echo >&2 " $program [-v] -l"
-       echo >&2 " $program -u"
-       echo >&2 " $program -h (this screen)"
-       echo >&2 ""
-       echo >&2 "Options:"
-       echo >&2 "  -c CODE: set the country code (default: $lc_country)"
-       echo >&2 "  -e NUM: set the base extension number (default: $base_exten)"
-       echo >&2 "  -m: set signalling method (gs/ks/ls, default: $method)"
-       echo >&2 "  -l: output a list of detected channels instead of zaptel.conf"
-       echo >&2 "  -u: Unload zaptel modules"
-       echo >&2 "  -v: verbose"
-       echo >&2 "  -r: rapid configuration mode: configure Zaptel FXS channels from "
-       echo >&2 "      existing Rapid extension files. FXOs will all be TRUNK "
-}
-
-# $1: channel number
-print_pattern() {
-       local chan=$1
-       local sig=$2 #fxs/fxo
-       local mode=$3
-       case "$mode" in
-       zaptel) echo "${sig}$method=$chan" ;;
-       list) echo $chan $sig;;
-       zapata)
-               echo "signalling=${sig}_$method"
-               if [ "$sig" = 'fxo' ]
-               then
-               echo "; Note: this is an extension. Create a ZAP extension in AMP for Channel $chan"
-        echo "context=from-internal"
-               echo "group=1"
-                       # to preconfigure channel 1's extension to 550, set
-                       # chan_1_exten=550
-                       # in, e.g, /etc/default/zaptel
-                 var_name=`echo chan_${chan}_exten`
-                       cfg_exten=`echo ${!var_name} | tr -d -c 0-9`
-                 var_name=`echo chan_${chan}_vmbox`
-                       cfg_vmbox=`echo ${!var_name} | tr -d -c 0-9`
-                 var_name=`echo chan_${chan}_cntxt`
-                       cfg_cntxt=`echo ${!var_name} | tr -d -c 0-9`
-                       
-                       # if option -E was given, get configuration from current extension
-                       if [ "$rapid_conf_mode" = 'yes' ]
-                       then
-                               rap_exten=`echo $rapid_extens |awk "{print \\$$rapid_cur_exten}"`
-                               if [ "$rap_exten" != '' ]
-                               then
-                                       rap_cfgfile="$exten_base_dir/$rap_exten.conf"
-                                       if [ -r "$rap_exten" ]
-                                       then
-                                               cfg_exten=$rap_exten
-                                               # the vmbox is the third parameter to stdexten
-                                               rap_vmbox=`grep '^[^;].*Macro(stdexten' $rap_exten | cut -d, -f3 \
-                                                       | cut -d')' -f1 | tr -d -c '0-9@a-zA-Z'`
-                                               if [ "$rap_vmbox" ]!= '' ; then cfg_vmbox=$rap_vmbox; fi
-                                       fi
-                               fi
-                               rapid_cur_exten=$(($rapid_cur_exten + 1))
-                       fi
-                       
-                       if [ "$cfg_exten" = '' ]
-                       then # No extension number set for this channel
-                               exten=$(($chan+$base_exten))
-                       else # use the pre-configured extension number
-                               exten=$cfg_exten
-                       fi
-                       # is there any real need to set 'mailbox=' ?
-                       if [ "x$cfg_vmbox" = x ]
-                       then # No extension number set for this channel
-                               vmbox=$exten
-                       else # use the pre-configured extension number
-                               vmbox=$cfg_vmbox
-                       fi
-                       # echo "callerid=\"Channel $chan\" <$exten>"
-                       # echo "mailbox=$exten"
-               else # we have may have set it. So reset it:
-                       echo "; Note: this is a trunk. Create a ZAP trunk in AMP for Channel $chan"
-                       echo "context=from-zaptel"
-                       echo "group=0"
-                       # echo "callerid=\"\" <0>"
-                       # echo "mailbox="
-               fi
-
-               echo "channel => $chan"
-               echo ""
-
-               # Keep a note of what channels we have identified
-               say "DEBUG: adding to channels list: channel: $chan, sig: $sig"
-               case "$sig" in
-               fxs)
-                       echo $chan >$tmp_dir/fxo_$chan
-                       say "DEBUG: FXO list now contains: `cat $tmp_dir/fxo_* |xargs`"
-                       ;;
-               fxo)
-                       echo $chan >$tmp_dir/fxs_$chan
-                       say "DEBUG: FXS list now contains: `cat $tmp_dir/fxs_* |xargs`"
-                       ;;
-               esac
-               ;;
-       esac
-       
-}
-
-# the number of channels from /proc/zaptel
-# must always print a number as its output.
-count_proc_zap_lines() {
-       # if zaptel is not loaded there are 0 channels:
-       if [ ! -d /proc/zaptel ]; then echo '0'; return; fi
-       
-       (
-               for file in `echo /proc/zaptel/* |grep -v '\*'`
-               do sed -e 1,2d $file # remove the two header lines
-               done
-       ) | wc -l # the total number of lines
-}
-
-load_modules() {
-       say "Test Loading modules:"
-       for i in zaptel $ALL_MODULES
-       do
-               if [ "$i" = ztdummy ]; then
-                       continue        # No hardware to detect
-               fi
-               lines_before=`count_proc_zap_lines`
-               args="${i}_args"
-               eval "args=\$$args"
-               # a module is worth listing if it:
-               # a. loaded successfully, and
-               # b. added channels lines under /proc/zaptel/*
-               if /sbin/modprobe $i $args 2> /dev/null && \
-                       [ $lines_before -lt `count_proc_zap_lines` ] 
-               then
-                       probed_modules="$probed_modules $i"
-                       say "   ok      $i      $args"
-               else
-                       say "   -       $i      $args"
-               fi
-       done
-}
-
-
-unload_modules() {
-       if
-               pids="$(pgrep asterisk)"
-               [ "$pids" != '' ]
-       then
-               die "Before unloading -- STOP asterisk (pids=$pids)."
-       fi
-       say "Unloading zaptel modules:"
-       modlist=''
-       for i in $ALL_MODULES zaptel
-       do
-               if lsmod | grep "^$i  *" > /dev/null; then
-                       modlist="$modlist $i"
-                       say -n "$i "
-               fi
-       done
-       /sbin/modprobe -r $modlist
-       say ''
-}
-
-detect() {
-       unload_modules
-       load_modules
-       modlist="$probed_modules"
-       #for i in $ALL_MODULES
-       #do
-       #       if lsmod | grep "^$i  *" > /dev/null; then
-       #               modlist="$modlist $i"
-       #       fi
-       #done
-       modlist="$(echo $modlist)"              # clean spaces
-       if [ "$modlist" = '' ]; then
-               modlist=ztdummy                 # Fallback
-       fi
-       say "Updating '${ZAPTEL_BOOT}'"
-       do_update ZAPTEL_MODS  "$modlist"
-}
-
-check_tdm_sigtype() {
-       chan_num=$1
-       sig_type=$2
-       mode=$3
-       
-       case "$sig_type" in
-       fxs)chan_sig_type=fxo;;
-       fxo)chan_sig_type=fxs;;
-       esac
-
-#      print_pattern $chan_num $chan_sig_type $mode
-       
-       $ztcfg_cmd -c <(print_pattern $chan_num $chan_sig_type zaptel) 2>/dev/null  \
-               || return 1
-       if head -c1 /dev/zap/$chan_num >/dev/null 2>/dev/null
-       then 
-               print_pattern $chan_num $chan_sig_type $mode
-               return 0
-       else
-               return 1
-       fi      
-}
-
-# output a list of extensions that need a channel
-get_rapid_extens() {
-       if [ "$rapid_conf_mode" = 'yes' ]
-       then
-               rapid_extens=`grep -l '^[^;].*Zap/\${CHAN_ZAP_' $exten_base_dir/*.conf 2>/dev/null | \
-                       rev | cut -d/ -f1 | cut -d. -f2- | rev | xargs`
-               say "Need to configure extensions: $rapid_extens"
-       fi
-}
-
-genconf() {
-       local mode=$1
-
-       # reset FXO list (global)
-       say "DEBUG: resetting channels lists"
-       rm -f $tmp_dir/fx{s,o}_*
-
-       if [ "$mode" = 'zapata' ]
-       then
-               rem_char=';'
-       else
-               rem_char='#'
-       fi
-
-       spanlist=`echo /proc/zaptel/* |  grep -v '\*'`
-
-       #if [ "$spanlist" == "" ]; then
-       #       die "No zapata interfaces in /proc/zaptel"
-       #fi
-
-
-       case "$mode" in 
-               zaptel)
-                       cat <<EOF
-# Autogenerated by $0 -- do not hand edit
-# Zaptel Configuration File
-#
-# This file is parsed by the Zaptel Configurator, ztcfg
-#
-
-# It must be in the module loading order
-
-EOF
-                       ;;
-               zapata)
-                       cat <<EOF
-; Autogenerated by $0 -- do not hand edit
-; Zaptel Channels Configurations (zapata.conf)
-;
-; This is not intended to be a complete zapata.conf. Rather, it is intended 
-; to be #include-d by /etc/zapata.conf that will include the global settings
-;
-callerid=asreceived
-EOF
-               ;;
-       esac
-
-       # For each line in the spanlist: see if it represents a channel.
-       # if it does, test that the channel is usable.
-       # we do that by configuring it (using ztcfg with a 1-line config file)
-       # and then trying to read 1 byte from the device file.
-       #
-       # The '<(command)' syntax creates a temporary file whose content is is the
-       # output of 'command'.
-       #
-       # This approach failed with the T1 card we have: the read operation simply 
-       # hung. 
-       #
-       # Another problem with such an approach is how to include an existing 
-       # configuration file. For instance: how to include some default settings.
-       #
-       # Maybe an 'include' directive should be added to zaptel.conf ?
-       #cat $spanlist | 
-       for procfile in $spanlist
-       do
-               # the first line is the title line. It states the model name
-               # the second line is empty
-               title=`head -n 1 $procfile`
-               echo ""
-               echo "$rem_char $title"
-               
-               # The rest of the lines are per-channel lines
-               sed -e 1,2d $procfile | \
-               while read line
-               do 
-                       # in case this is a real channel. 
-                       chan_num=`echo $line |awk '{print $1}'`
-                       case "$line" in
-                       *WCT1/*) # we're yet to detect when a channel is active
-                               echo "$rem_char channel $chan_num, WCT1, unhandled for now"
-                               ;;
-                       *WCTDM/*) 
-                               # this can be either FXS or FXO
-                               check_tdm_sigtype $chan_num fxs $mode || \
-                               check_tdm_sigtype $chan_num fxo $mode || \
-                               echo "$rem_char channel $chan_num, WCTDM, inactive."
-                               ;;
-                       *WRTDM/*) 
-                               # this can be either FXS or FXO
-                               check_tdm_sigtype $chan_num fxs $mode || \
-                               check_tdm_sigtype $chan_num fxo $mode || \
-                               echo "$rem_char channel $chan_num, WRTDM, inactive."
-                               ;;
-                       *WCFXO/*) 
-                               check_tdm_sigtype $chan_num fxo $mode || \
-                               echo "$rem_char channel $chan_num, WCFXO, inactive."
-                               ;;
-                       '') ;;          # Empty line (after span header)
-                       *) echo "$rem_char ??: $line";;
-                       esac
-               done
-       done
-
-       if [ "$mode" = 'zaptel' ]
-       then
-               cat <<EOF
-
-# Global data
-
-EOF
-               echo "loadzone  = $loadzone"
-               echo "defaultzone       = $defaultzone"
-       fi
-       
-       if [ "$mode" = 'zapata' ]
-       then 
-               update_extensions_defs 
-       fi
-}
-
-while getopts 'c:de:E:hlm:rsuv' arg
-do
-       case "$arg" in
-               e) # guarantee that it is a number:
-                       new_base_exten=`echo $OPTARG | tr -d -c 0-9`
-                       if [ "x$new_base_exten" != x ]; then base_exten=$new_base_exten; fi
-                       ;;
-               c) lc_country=`echo $OPTARG | tr -d -c a-z` ;;
-               u) do_unload=yes ;;
-               v) verbose=yes ;;
-               l) mode='list' ;;
-               m) 
-                 case "$OPTARG" in 
-                       k|l|g)method=${OPTARG}s ;;
-                       *) echo >&2 "unknown signalling method ${OPTARG}s, defaulting to \"$method\"";;
-                       esac
-                       ;;
-               r) 
-                       rapid_conf_mode=yes 
-                       tmp_dir=`mktemp -d` || die "$0: failed to create temporary directory. Aborting"
-                       ;;
-               *) echo >&2 "unknown parameter -$arg, Aborting"; usage; exit 1;;
-       esac
-done
-shift $(( $OPTIND-1 ))
-if [ $# != 0 ]; then
-       echo >&2 "$0: too many parameters"
-       usage
-       exit 1
-fi
-
-case "$lc_country" in
-       # the list was generated from the source of zaptel:
-       #grep '{.*[0-9]\+,.*"[a-z][a-z]"' zonedata.c | cut -d'"' -f 2 | xargs |tr ' ' '|'
-       us|au|fr|nl|uk|fi|es|jp|no|at|nz|it|gr|tw|cl|se|be|il)
-       :;;
-*)
-  lc_country=us
-  echo >&2 "unknown country-code $lc_country, defaulting to \"us\"";;
-esac
-# any reason for loadzone and defaultzone to be different? If so, this is
-# the place to make that difference
-loadzone=$lc_country
-defaultzone=$loadzone
-
-# Choose reasonable default for signaling method (by country)
-if [ "" = "$method" ]; then
-       case "$lc_country" in
-       il) method=ls   ;;
-       *) method=ks    ;;
-       esac
-fi
-
-# make sure asterisk is not in our way
-if [ "$force_stop_ast" = 'yes' ]
-then
-#  /etc/init.d/asterisk stop 1>&2
-   /usr/sbin/amportal stop 1>&2
-else
-       if ps auxww |grep asterisk | grep -v -- -r | grep -q -v grep
-       then
-         echo >&2 "Asterisk is already running. Configuration left untouched"
-               echo >&2 "You can use the option -s to shut down Asterisk for the"
-               echo >&2 "duration of the detection."
-               exit 1
-       fi
-fi
-
-if [ "$do_unload" = yes ]
-then
-       unload_modules
-       exit
-fi
-
-if [ "$do_detect" = yes ]
-then
-       detect
-fi
-
-if [ "$mode" = list ]; then
-       genconf list
-else
-       get_rapid_extens
-       echo "Generating  '${ZAPCONF_FILE}'"
-       mv "${ZAPCONF_FILE}" "${ZAPCONF_FILE}.bak"
-       genconf zaptel > "${ZAPCONF_FILE}"
-       echo "Generating  '${ZAPATA_FILE}'"
-       mv "${ZAPATA_FILE}" "${ZAPATA_FILE}.bak"
-       genconf zapata > "${ZAPATA_FILE}"
-       run_ztcfg
-fi
-
-if [ "$force_stop_ast" = 'yes' ]
-then
-#  /etc/init.d/asterisk start 1>&2
-       /etc/init.d/zaptel stop
-       /etc/init.d/zaptel start
-       /usr/sbin/amportal start 1>&2
-fi
-
-# if in verbose mode: verify that asterisk is running
-if [ "$verify" != 'no' ]
-       then
-       say "Checking channels configured in Asterisk:"
-       sleep 1 # give it some time. This is enough on our simple test server
-       /usr/local/sbin/ast-cmd cmd "zap show channels"
-fi