/[smeserver]/cdrom.image/sme10/Packages/base/sme-kickstart.cfg
ViewVC logotype

Diff of /cdrom.image/sme10/Packages/base/sme-kickstart.cfg

Parent Directory Parent Directory | Revision Log Revision Log | View Revision Graph Revision Graph | View Patch Patch

Revision 1.3 by unnilennium, Tue May 31 12:37:44 2016 UTC Revision 1.6 by chrissn, Tue Dec 29 15:12:14 2020 UTC
# Line 1  Line 1 
1  # System authorization information  # System authorization information
2  auth --enableshadow --passalgo=sha512  auth --enableshadow --passalgo=sha512
 # Use CDROM installation media  
 cdrom  
 # we do not want Selinux  
 selinux --disabled  
 # services to activate  
 services --disabled=lm_sensors  
 # default root pass, willbe changed in post-install process anyway  
 rootpw --lock  
   
 # include the partitioning logic from the pre section.  
 %include /tmp/part-include  
   
 %pre  
 # pre section  
 #----- partitioning logic below--------------  
 # pick the first drive that is not removable and is over MINSIZE  
 DIR="/sys/block"  
   
 # minimum size of hard drive needed specified in GIGABYTES  
 MINSIZE=20  
   
 ROOTDRIVE=""  
   
 # /sys/block/*/size is in 512 byte chunks  
   
 for DEV in sda sdb sdc sdd hda hdb vda vdb xvda xvdb; do  
   if [ -d $DIR/$DEV ]; then  
     REMOVABLE=`cat $DIR/$DEV/removable`  
     if (( $REMOVABLE == 0 )); then  
       echo $DEV  
       SIZE=`cat $DIR/$DEV/size`  
       GB=$(($SIZE/2**21))  
       if [ $GB -gt $MINSIZE ]; then  
         echo "$(($SIZE/2**21))"  
         if [ -z $ROOTDRIVE ]; then  
           ROOTDRIVE=$DEV  
         fi  
       fi  
     fi  
   fi  
 done  
   
 echo "ROOTDRIVE=$ROOTDRIVE"  
   
 # drives smaller than 40GB use smaller boot and swap partitions  
 # drives larger than 40GB use percentage-based partition sizes  
3    
4  if [ $GB -lt 40 ]; then  # We do not want SELinux
5    selinux --disabled
6    
7  # drives smaller than 40GB  # Services to activate
8  cat << EOF > /tmp/part-include  services --disabled=lm_sensors
 zerombr  
 clearpart --all --drives=$ROOTDRIVE --initlabel  
 bootloader --location=mbr --driveorder=$ROOTDRIVE  
 # for boot partition  
 part /boot --fstype ext4 --size=300 --ondisk=$ROOTDRIVE  
 # for LVM partition  
 part pv.8 --size=4600 --grow --ondisk=$ROOTDRIVE  
 # LVM  
 volgroup main --pesize=65536 pv.8  
 logvol / --fstype ext4 --name=root --vgname=main --grow --size=3000  
 logvol swap --fstype swap --name=swap --vgname=main --size=1500  
9    
10  EOF  # Default root pass, will be changed in post-install process anyway
11    rootpw --lock
12    
13    # Accept EULA
14    eula --agreed
15    
16  else  # Partitioning from pre section
17  # drives 40GB and larger  %include /tmp/part-include
18    
19  cat << EOF > /tmp/part-include  # Disable kdump
20  zerombr  %addon com_redhat_kdump --disable
21  clearpart --all --drives=$ROOTDRIVE --initlabel  %end
 bootloader --location=mbr --driveorder=$ROOTDRIVE  
 # for boot partition  
 part /boot --fstype ext4 --size=500 --ondisk=$ROOTDRIVE  
 # for LVM partition  
 part pv.8 --size=4600 --grow --ondisk=$ROOTDRIVE  
 # LVM  
 volgroup main --pesize=65536 pv.8  
 logvol / --fstype ext4 --name=root --vgname=main --grow  --size=3000  
 logvol swap --fstype swap --name=swap --vgname=main --size=4000  
22    
 EOF  
23    
24  fi  # Add netinstall repos
25    repo --name=smeos --baseurl=http://mirror.canada.pialasse.com/releases/testing/10/smeos/x86_64/
26    repo --name=smeupdates --baseurl=http://mirror.canada.pialasse.com/releases/testing/10/smeupdates/x86_64/
27    
28    # Packages to install
29    %packages
30    @^minimal
31    @base
32    @core
33    -chrony
34    -kexec-tools
35  %end  %end
36    
37    
38    # Partitioning in pre-install
39    %pre --interpreter=/bin/bash --log=/var/log/ks.pre01.log
40    
41    # Minimum size of hard drive needed specified in GB
42    MINSIZE=5
43    
44    # Number of detected drives
45    NDEV=0
46    
47    # Loop through block devices and keep those over MINSIZE
48    # TODO: Only pair up drives of the same size
49    for DEV in $(lsblk -nl | grep disk | cut -d' ' -f1); do
50      if [ -d /sys/block/$DEV ]; then
51        REMOVABLE=`cat /sys/block/$DEV/removable`
52        if (( $REMOVABLE == 0 )); then
53          SIZE=`cat /sys/block/$DEV/size`
54          GB=$(($SIZE/2**21))
55          if [ $GB -gt $MINSIZE ]; then
56            DRIVES[$NDEV]=$DEV
57            ((NDEV++))
58          fi
59        fi
60      fi
61    done
62    
63    # Declare useful variables
64    printf -v DRIVELIST ",%s" "${DRIVES[@]}"
65    DRIVELIST=${DRIVELIST:1}
66    LEVEL=1
67    SPARE=0
68    
69    # Error if detection has failed and fall back
70    if [ ${#DRIVES[@]} == 0 ] ; then
71      echo "No drive suitable for installation found! Reverting to Anaconda defaults."
72    
73      cat > /tmp/part-include <<EOF
74      # Clear the Master Boot Record
75      zerombr
76    
77      # Clear current partitions
78      clearpart --all  --initlabel
79    
80      # Automatically create partitions using LVM
81      autopart --lvm --nohome
82    EOF
83    
84    # Otherwise clear detected devices and set up bootloader
85    else
86      cat > /tmp/part-include <<EOF
87      # Clear the Master Boot Record
88      zerombr
89    
90      # Clear current partitions and install bootloader
91      clearpart --all --drives=$DRIVELIST --initlabel
92      ignoredisk --only-use=$DRIVELIST
93      bootloader --location=mbr --driveorder=$DRIVELIST
94    EOF
95    
96      # If single disk then set up partitioning without RAID
97      # NOTE: From this point we're appending to part-include
98      if [ ${#DRIVES[@]} == 1 ] ; then
99    
100        # Include the EFI partition if necessary
101        if [ -d /sys/firmware/efi ] ; then
102          printf "part /boot/efi --fstype=efi --size=200 --ondisk=%s\n" "${DRIVES[0]}" >> /tmp/part-include
103        fi
104    
105        cat >> /tmp/part-include <<EOF
106        part /boot --fstype=xfs --size=500 --ondisk=${DRIVES[0]} --label=BOOT
107        part pv.01 --size=4300 --grow --ondisk=${DRIVES[0]}
108        volgroup main pv.01
109        logvol / --fstype=xfs --name=root --vgname=main --grow --size=3000 --label=ROOT
110        logvol swap --fstype=swap --name=swap --vgname=main --recommended --label=SWAP
111    EOF
112    
113      # Otherwise multiple disks - prepare for RAID
114      else
115    
116        # Define EFI, boot and LVM RAID partitions
117        for i in "${!DRIVES[@]}"; do
118          if [ -d /sys/firmware/efi ] ; then
119            printf "part raid.%s0 --size=200 --ondisk=%s\n" "$i" "${DRIVES[$i]}" >> /tmp/part-include
120          fi
121          printf "part raid.%s1 --size=500 --ondisk=%s\n" "$i" "${DRIVES[$i]}" >> /tmp/part-include
122          printf "part raid.%s2 --size=4300 --grow --ondisk=%s\n" "$i" "${DRIVES[$i]}" >> /tmp/part-include
123        done
124    
125        # Compute RAID level
126        # from https://wiki.contribs.org/Raid
127        # 2 Drives - Software RAID 1
128        # 3 Drives - Software RAID 1 + 1 Hot-spare
129        # 4 Drives - Software RAID 6
130        # 5+ Drives - Software RAID 6 + 1 Hot-spare
131    
132        if [ ${#DRIVES[@]} == 2 ] ; then
133          LEVEL=1
134          SPARE=0
135        elif [ ${#DRIVES[@]} == 3 ] ; then
136          LEVEL=1
137          SPARE=1
138        elif [ ${#DRIVES[@]} == 4 ] ; then
139          LEVEL=6
140          SPARE=0
141        else
142          LEVEL=6
143          SPARE=1
144        fi
145    
146        # Set up RAID devices
147        printf -v EFIDEVS "raid.%s0 " "${!DRIVES[@]}"
148        printf -v BOOTDEVS "raid.%s1 " "${!DRIVES[@]}"
149        printf -v ROOTDEVS "raid.%s2 " "${!DRIVES[@]}"
150        
151        # Include the EFI partition if necessary
152        if [ -d /sys/firmware/efi ] ; then
153          printf "raid /boot/efi --fstype=efi --level=1 --spares=0 --device=md9 %s\n" "$EFIDEVS" >> /tmp/part-include
154        fi
155    
156        printf "raid /boot --fstype=xfs --level=1 --spares=0 --device=md0 %s\n" "$BOOTDEVS" >> /tmp/part-include
157        printf "raid pv.01 --level=%s --spares=%s --device=md1 %s\n" "$LEVEL" "$SPARE" "$ROOTDEVS" >> /tmp/part-include
158    
159        # Set up LVM
160        cat >> /tmp/part-include <<EOF
161        volgroup main pv.01
162        logvol / --fstype xfs --name=root --vgname=main --grow --size=3000 --label=ROOT
163        logvol swap --fstype swap --name=swap --vgname=main --recommended --label=SWAP
164    EOF
165    
166  # packages to install    fi
167  %packages  fi
 @^minimal  
 @base  
 @core  
 -chrony  
 -kexec-tools  
168    
169  %end  %end
170    
171    
172  # pre script could be inserted there to handle partitionning  # SME events in post-install
173    %post  --interpreter=/usr/bin/bash --log=/var/log/ks.post02.log
174  %post  --interpreter=/usr/bin/bash  /sbin/rsyslogd;
175  # before reboot performing post-install  sleep 2;
176  # this is for first alpha iso. we should put this in anaconda  /sbin/e-smith/signal-event post-install;
 # and / or handle possible upgrade later  
 /sbin/rsyslogd;  
 sleep 2;  
 /sbin/e-smith/signal-event post-install;  
177  sleep 2;  sleep 2;
178  /sbin/e-smith/db configuration set UnsavedChanges no;  /sbin/e-smith/db configuration set UnsavedChanges no;
179  touch /forcequotacheck  touch /forcequotacheck
180    %end
181    
182    
183    %post  --nochroot --log=/mnt/sysimage/var/log/ks.post01.log
184    #!/bin/bash
185    sysimage="/mnt/sysimage"
186    cp -r /tmp/anaconda.log ${sysimage}/root/
187  %end  %end

Legend:
Removed lines/characters  
Changed lines/characters
  Added lines/characters
admin@koozali.org
 ViewVC Help
Powered by ViewVC 1.2.1 RSS 2.0 feed